You can view and edit one channel, or you can view all four channels at the same time (not editable).To switch between these two modes, simply click the View button below the three vertical control bars.When the vertical grid is displayed, you can draw the modulation data.After drawing the shape, click again to display the 4D display.Blue represents the minimum price and red represents the high price. The second selects the vertical edit range and the third bar selects the modulation channel shown on the display. Modulation Table: The third table in the sequencer is a 3-channel modulation sequencer, which allows you to draw and edit four different modulations individually.You can route the modulation to the synth parameters in the matrix modulation section.Similar to the pitch sequencer, on the right side of the modd sequencer are three vertical bars, each with different functions. Note that the Blue Matrix sequencer has separate pitches and gates.The sequencer sends pitch information even in the absence of a gate signal.That is, you can create a custom glide.The glide time is set with the small glide knob on the left side of the pitch table.If the glide value is small, the oscillator pitch reflects what is displayed in the pitch table.Larger glide values create ramps, or smoothings, from one pitch to the next.In leg (legato) mode, glide is active only for overlapping notes. P Inc sets how much the pitch is incremented in semitones when data is inserted or pasted.For example, if you want to transpose a diagram by 5 semitons, place horizontal and vertical edit bars to fit the length of the diagram and press Copy to insert.Similarly, V inc sets the speed increment for pasted or inserted data.ĭata Randomization and Quantization: In addition to copying and pasting the range indicated by the edit bar, you can also randomize the data within this range.Simply click on a land to fill the edit area with a random pitch.The properties of that pitch are determined by the Hold, Retrigger, and N features.The data in the editing range can also be quantized at the resolution set in using the button.Undo features can be used to copy / paste, randomize, quantize, clear, and record data in tables.Gate table and glide: Below the pitch table is a table where you can draw gate (note-on) events.The height of the event corresponds to the speed. The edit range can be expanded by clicking and dragging near the top or bottom.The edit range can be dragged up or down by clicking and dragging in the center.An additional horizontal editor bar is provided to allow you to select notes in time.The copy / paste / cut / insert functions to the right of the vertical bar perform normal functions (for areas defined by the horizontal and vertical edit bars). The first is the vertical zoom / scroll bar.Click near the top or bottom of this bar and drag it to act as a zoom, but drag the center of the bar to scroll the display.The next vertical bar sets the trigger threshold.Notes below this threshold will not be triggered. Important note! !!Note that the complete sequencer is based on Reaktor's event table, so the table data and snapshot data are independent of each other.Snapshots correctly save the positions of all knobs associated with the sequencer, but not table data.Of course, you can set your own sequence for each snapshot, but it's important to note that the Global Seq knob is set to the same number as the current snapshot.Otherwise, if different presets share the same table Seq, you can change the table sequence and accidentally change the sound of all other snapshots that use the same table.You can work around this issue if each snapshot has a unique Seq number.However, keep in mind that table data is excluded from snapshot features such as morphing, randomization, and comparison.For really safety, if you spend a lot of time on your favorite sequence, use the Save As… command to save the entire ensemble.Pitch table: There are three vertical bars on the right side of the pitch edit table. Data can be saved and edited.There are numerous horizontal and vertical control bars for selecting the "edit" range of commands such as zoom, sequence length selection, randomization, quantization, copy / paste / insert.Īll notes below the threshold are interpreted as note-off.If the trigger event does not appear in the Retrigger sequencer below, a trigger is automatically generated. The field contains four independent tracks with additional modulations. ![]() The Blue Matrix sequencer consists of three areas where you can draw sequencer data-the top handles the pitch of the notes in the sequence, the bottom field shows the trigger and velocity information for those notes, and finally.
0 Comments
Leave a Reply. |